克鲁勃GH 6-100合成高温齿轮油

详细内容：产品基本信息： 型号：synth GH 6-100 英文名称:KLUBERsynth GH 6-100 粘度等级：ISO VG 100 品牌/产地：克鲁勃，德国 包装规格及价格：20L/3600 200L/28000 类型：合成高温齿轮油 宝贝描述： Klubersynth GH 6-(32,80,150,220,320,460,680,1000)合成高温齿轮油。 说明：Klübersynth GH6高温聚乙二醇齿轮油基础。他们有增加的划伤提供良好的负载能力和保护，防止磨损。严格的FZG试验（A/16.6/140），这些油有划伤加载阶段> 12并在重量与工作有关的损失≤0.2毫克/千瓦时。 Klübersynth GH6特别是抗老化和氧化，他们有一个良好的粘温关系并显示出优异的高温行为。 应用领域：Klübersynth GH6特别是制定了蜗杆与齿轮润滑钢/铜配对。在这应用程序有两个有趣的方面：特殊的聚乙二醇基地油降低了摩擦系数，和非常有效的添加剂最大限度地减少磨损。Klübersynth GH6也适用润滑所有类型的斜面与正齿轮，滑动与滚动轴承以及齿联轴器，特别是当接触到温度升高。 特性： 合成齿轮高温油 优异的粘温的关系 宽工作温度的范围 减少摩擦 高划伤负载能力 良好的抗磨损性能。 包装规格：20升罐200升鼓 德文： Klübersynth GH 6 Oils Synthetic gear and high-temperature oils Description: Klübersynth GH 6 oils are high-temperature gear oils on a polyglycol basis. They have an increased scuffing load capacity and provide good protection against wear. In the stringent FZG test (A/16.6/140) these oils had a scuffing load stage > 12 and a work-related loss in weight ≤ 0.2 mg/kWh. Klübersynth GH 6 oils are particularly resistant to ageing and oxidation, they have a good viscosity-temperature relationship and show an excellent hightemperature behaviour. Fields of application: Klübersynth GH 6 oils were especially developed for the lubrication of worm gears with steel/bronze pairings. In this application there are two interesting aspects: the special polyglycol base oils reduce the friction coefficient, and the very efficient additives minimize wear. Klübersynth GH 6 oils are also suitable to lubricate all types of bevel and spur gears, plain and rolling bearings as well as toothed couplings, especially when exposed to increased temperatures. Application notes: Klübersynth GH 6 oils can be applied by immersion, immersion circulation and injection. Observe the manufacturer’s instructions about the maximum viscosity that can be pumped. Klübersynth GH 6 oils are not miscible with mineral oils and synthetic hydrocarbons. We recommend cleaning the lubrication points prior to conversion, and rinsing gears or closed lubricating systems with the Klübersynth GH 6 oil that will be used for lubrication. Klübersynth GH 6 oils are neutral towards ferrous materials and almost all nonferrous metals. There may be increased wear when the contact surfaces of design elements made of aluminium or aluminium alloys are exposed to dynamic loads (sliding speed and high loads). If necessary, wear tests should be carried out. Depending on temperature and exposure time, synthetic lubricants on a polyglycol base may have an impact on the functional capacity of rubber-elastic sealing materials. Seals made of NBR materials (acrylonitrile-butadiene-rubber) can be used at permanent temperatures up to 100 °C. For higher temperatures we recommend to use seals made of FKM materials (fluorinated rubber), i. e. elastomers which are resistant to Klübersynth GH 6 oils. It has to be taken into account that different elastomer qualities produced by one manufacturer or different manufacturers may show a different behaviour. For approximate values about a change in volume and hardness of NBR and FKM materials in contact with Klübersynth GH 6 oils refer to the table “compatibility with elastomers”. Paints may be attacked by synthetic lubricants. When applying Klübersynth GH 6 oils we recommend the use of two-component paints (reactive paints) for interior coating. Oil gauge glasses should preferably be made of natural glass or polyamide materials. Other transparent plastics, e. g. Plexiglas, have a tendency to crack under stress. We recommend testing the suitability of design materials and paints in contact with the selected lubricants, especially for series application. Viscosity selection for rolling bearings and gears: Selection of the correct oil viscosity for rolling bearings To select the correct oil viscosity observe the bearing manufacturer’s instructions or refer to GfT worksheet 3 (GfT = Society of Tribology). For determining the existing viscosity, refer to the enclosed viscositytemperature diagram indicating the differing viscosity-temperature behaviour of Klübersynth GH 6 oils as compared to mineral oils. Selection of the correct oil viscosity for gears The manufacturer’s instructions take priority in all cases. The correct viscosity can also be selected in accordance with the enclosed worksheet “Klübersynth GH 6 oils – Selection of oil viscosity for gears”. Service temperature range: Gear and chain lubrication by immersion: Klübersynth GH 6-32: from approx. – 45 °C to 160 °C Klübersynth GH 6-80 … 150: from approx. – 35 °C to 160 °C Klübersynth GH 6-220 and -320: from approx. – 30 °C to 160 °C Klübersynth GH 6-460 … 1000: from approx. – 25 °C to 160 °C Klübersynth GH 6-Oils Synthetic gear and hightemperature oil Excellent viscosity-temperature relation Wide service temperature range Reduces friction High scuffing load capacity Good antiwear properties