Kluber 4 UH 1-680 N/1500 N齿轮油

详细内容：产品基本信息： 型号：oil 4 UH1-680 N/1500 N 英文名称:Kluberoil 4 UH1-680 N/1500 N 粘度等级：ISO VG 32 品牌/产地：克鲁勃，德国 包装规格及价格：20L/3580 200L/27000 类型：食品级润滑油 宝贝描述： Klüberoil 4 UH1-32...1500 N是用于食品加工润滑剂和制药业。他们满足的要求德国法律管辖食品和相关辅助设备（LMBG，秒5，第1句，1）和美国提出的要求证券交易委员会21 CFR“准则FDA的规定“和178.3570是符合要求NSF H1注册。Klüberoil4 UH1-68...1500 N油符合中电的要求。当测试在FZG齿轮试验台根据根据DIN51354，第2部分，A /8,3/90，油呈划伤负载> 12和具体损失重量<0.2毫克/千瓦时。特别是制定了在使用食品加工和制药产业，这些润滑油展良好的抗磨损和极压性能以及优秀lowtemperature特征。腐蚀防护性能这些油都是很好的作为是他们的老化和氧化稳定性。他们因此，有一个高抗剪切并没有泡沫。 应用：Klüberoil4 UH1用于润滑的摩擦点在食品加工和制药机械。它们尤其适合为鞭策，斜面和润滑蜗杆齿轮，轴承，主轴和关节，以及电梯，驱动器和在低温下输送链。 包装规格：20升罐200升鼓 英文： Klüberoil 4 UH 1-32 N … 1500 N oils Synthetic lubricating oils for the food-processingand pharmaceutical industries Description Klüberoil 4 UH 1-32 N…1500 N oils are lubricants for the food processing and pharmaceutical industry. They meet the requirements of the German law governing food products and associated ancillaries (LMBG, sec. 5, para 1, sentence 1) and the US requirements set forth in the "Guidelines of sec. 21 CFR 178.3570 of FDA regulations" and are in line with the requirements of NSF H1 registration. Klüberoil 4 UH 1-68…1500 N oils meet the CLP requirements. When tested on the FZG gear test rig according to DIN 51 354, part 2, A/8,3/90, the oils showed a scuffing load of > 12 and a specific loss of weight of < 0.2 mg/kWh. Especially formulated for use in the food-processing and pharmaceutical industries, these lubricating oils exhibit good antiwear and EP properties as well as excellent lowtemperature characteristics. The corrosion protection properties of these oils are very good as is their ageing and oxidation stability. They also have a high resistance to shear and do not foam. Application Klüberoil 4 UH 1 oils are used for the lubrication of friction points in foodprocessing and pharmaceutical machinery. They are especially suitable for the lubrication of spur, bevel and worm gears, bearings, spindles and joints, as well as of lift, drive and conveyor chains at low temperatures. Application notes When used in gears, Klüberoil 4 UH 1 oils may be applied by immersion, immersion circulation or injection. Drip-feed lubrication (e.g. for chains) and application by brush or oil can is also possible.Klüberoil 4 UH 1 oils are miscible with mineral oils and polyalfaolefin oils. However, we recommend cleaning the oil circulation system or flushing it with the new oil prior to using Klüberoil 4 UH 1 for the first time. Especially with a view to the H1 requirements in the foodprocessing industry, any mixing of Klüberoil 4 UH 1 oils with non-foodgrade lubricants should be avoided. For permanent temperatures at the seal edge up to 100 °C, NBR seals (acrylonitrile-butadiene rubber) may be used. For higher temperatures, it is safer to use FKM seals (fluorinated rubber) instead. It should be noted that elastomers from one or several manufacturers can behave differently. Therefore the data given in the "compatibility with elastomers" table should be used for reference purposes only. A compatibility test should always be carried out with the elastomers which are actually used. Viscosity selection for rolling bearings and gears To select the correct oil viscosity, observe the bearing manufacturer's instructions or refer to worksheet 3 from the Society of Tribology (GfT). For determining the correct viscosity for gears, the manufacturer's instructions take priority. Only in cases where there are no gear manufacturer's instructions, the viscosity can be selected in accordance with the enclosed worksheet "Klüberoil 4 UH 1 oils – selection of oil viscosity for gears". Service temperature range*: ISO VG 32 to 100 approx. - 35 °C to approx. 120 °C ISO VG 150 to 460 approx. - 30 °C to approx. 120 °C ISO VG 680 to 1500 approx. - 25 °C to approx. 120 °C When used for loss lubrication, the lubricant may be exposed to higher temperatures, depending on the relubrication intervals. We will be pleased to provide samples for testing. * Service temperature range: Service temperatures are guide values which depend on the lubricant's composition, the intended use and the application method. Lubricants change their consistency, viscosity or apparent dynamic viscosity depending on the mechano-dynamical loads, time, pressure and temperature. These changes in product characteristics may affect the function of a component. Minimum shelf life The minimum shelf life is approx. 24 months if the product is stored in the original closed container in a dry place. Pack sizes 400 ml spray can (ISO VG 1500) 5 l canister 20 l canister 200 l drum